中文版 English 收藏本站 关于天力

天力磁电

全国免费服务热线400-1122-958

您当前所在位置:首页 > 新闻中心 > 专业选矿除铁技术

陶瓷行业专用除铁机的常见故障有哪些?

作者:管理员     发布于:2017-03-29    

(1除铁机电机过热及其声响不正常。

(1 iron removal machine overheating and abnormal sound.

除铁机电机过热及其声响不正常的原因: 1)轴承润滑不良或磨损严重;2)风扇叶脱落或磨损;3)开关线路接触不良或断线跑单相;4)电压过低。

In addition to the iron motor overheating and abnormal sound reasons: 1) bearing lubrication is bad or wear serious; 2) fan leaf fall off or wear; 3) switch line bad contact or broken line run single phase; 4) voltage is too low.

(2)除铁机在运转中声响不正常,圆筒被障碍物卡住,甚至使圆筒不能转动,底箱颤动。

(2) in addition to the abnormal operation of the iron in the operation, the cylinder is jammed, even the cylinder can not rotate, the bottom of the box fibrillation.

其原因往往是被底箱的物体卡住,再就是磁块脱落,使筒体嘎嘎作响,严重时会使筒皮划破。这时应停止设备运行,检修并排除故障。

The reason is often stuck in the bottom of the box, and then the magnetic block off, so that the cylinder rattle, seriously when the cylinder will be cut. At this point, the operation of the equipment should be stopped.

(3)减速机过热

(3) overheating of reducer

其原因:1)油量不足或油质不良;2)齿轮与蜗杆磨损过甚或啮合不好;3)轴承润滑不良或磨损严重。

The reasons: 1) the oil quantity is insufficient or the oil quality is bad; 2) the gear and the worm wear or even the meshing is not good; 3) the bearing lubrication is bad or the abrasion is serious.

(4)除铁机磁场强度变弱

(4) the magnetic field strength of iron removing machine is weak

其原因:1)温度过高;2)阳光暴晒;3)酸碱腐蚀。可以用高斯计测量。除铁机由机座、下磁系、转笼、上磁系、空心轴、精矿槽、传动装置等组成。安装机座以空心轴瓦座为基准测量其标高和水平度。下磁系的定位以机座为基准。转笼与上、下磁系的间隙调整必须准确,其间隙极限偏差为手0+1mm。

The reasons: 1) temperature is too high; 2) sun exposure; 3) acid corrosion. Can be measured with Gauss meter. The iron removing machine is composed of a machine frame, a lower magnetic system, a rotating cage, an upper magnetic system, a hollow shaft, a concentrate trough and a transmission device. The base of the mounting frame is measured with the hollow bearing block as its base. The orientation of the lower magnetic system is based on the base. The clearance between the rotor and the upper and lower magnetic system must be accurate, and the clearance limit deviation is 0+1mm.



天力首页 成功案例 解决方案
售后服务 技术支持 售后服务
新闻中心 企业新闻 选矿技术
关注我们 收藏网址
400-1122-958 周一至周六8:00-17:00 QQ在线客服
天力磁电

公司总部地址:浙江省东阳市经济开发区书院路11号 版权所有 © 2020 东阳市天力磁电有限公司 技术支持:蜂窝在线网络技术(浙江)有限公司  网站备案许可证号:浙ICP备15032298号-2

 微信二维码    手机网站

400-1122-958